Princeton-tec BYTE Bedienungsanleitung PDF herunterladen

www.princetontec.com

ENGLISH

Figure 1 – Switch Operation

Opération de commutation Betriebsartenschalter

* Princeton Tec calculates total burn time as the time it takes for the light source to produce a

minimum of 0.25 lux at 2 meters. 0.25 lux is about the equivalent of a full moon on a clear night.

* Princeton Tec berechnet die Gesamtbrenndauer bezogen auf eine von der Stirnlampe erzeugte

minimale Beleuchtungsstärke von 0,25 Lux in 2 Meter Abstand. 0,25 Lux entsprechen in etwa

der Beleuchtungsstärke des Vollmonds in einer klaren Nacht.

* Princeton Tec définit la durée totale d’éclairage comme le temps nécessaire à la source

lumineuse pour produire un minimum de 0,25lux à 2mètres. 0,25lux équivaut à peu près à la

luminosité d’une pleine lune dans un ciel nocturne dégagé.

BYTE

LED HEADLAMP

Operating and Maintenance

Instructions

Notice d’utilisation et d’entretien

Bedienungsanleitung

Battery Installation – See Battery Installation Diagram

• 2 AAA

• Alkaline (LR03) or Lithium

• Rechargeable NiCad or NiMH

Princeton Tec cares about the environment and

recommends recycling batteries. For more information

about battery recycling, please go to: www.batteryrecy-

cling.com

To install the batteries, unlatch the battery door. Open

the Byte case by popping the door latch over the catch

and rotate the door open.

Install two AAA batteries as shown in the diagram. The

tall spring on the battery door should correspond with

the negative polarity and the shorter spring on the

battery door should correspond with the positive

polarity. Observe proper battery polarity when installing

the batteries. Improper installation of the batteries will

damage the light and void the warranty.

Rotate the door to the closed position, squeeze the

body between your forefingers and thumb to snap the

door latch over the catch.

WARNING

• Never mix fresh and used batteries.

• Never mix different battery brands or

chemistry types.

• Always remove drained batteries immediately.

• Remove batteries during long periods of storage.

NOTE: Rechargeable NiCad or NiMH batteries may

result in reduced brightness due to lower nominal

voltage.

Battery Lockout - See Battery Lockout diagram

The Byte has a battery lockout switch integrated into

the battery door. While we still recommend removing

the batteries for prolonged storage, this lockout switch

ensures that the light cannot be turned on accidentally,

and completely eliminates battery drain.

Switch Operation – See Switch Operation diagram

The Byte has two light sources to choose from: one

3mm Red LED and one Maxbright white LED. The Red

LED always turns on first, followed by the Maxbright

LED in low mode, then high mode.

To turn the light on or switch to the Maxbright LED

modes, press and release the power button until the

desired mode is obtained.

To turn the light off, cycle through the remaining modes

until you reach off. Alternatively, the battery lockout

switch will turn Byte off immediately.

*The times listed on the rear of the package assume

beginning with fresh batteries and only using one

mode.

Troubleshooting

If the Byte fails to light:

• Check that the battery lockout switch is in the up/on

position.

• Check the batteries for proper installation.

• Replace batteries if proper installation is

confirmed.

• Check the light for water contamination.The light will

resume normal operation once the water is shaken

or blown out and the light is left open until

completely dry. If the light has been contaminated

with salt water, flush the unit with fresh water and

dry as described above.

Notice:

The Byte has 3 modes. The light will always come on

in the Red LED mode. After the Red LED mode, the

Byte will circulate to the white LED (low, then high).

Please note that after 2 hours of use on the high mode

of the white LED, the Byte will only have one output

mode in the white LED, and there will be no difference

in the beam strength when you press to switch to high

output mode.

USA– International 5-Year Warranty

WARRANTY – Princeton Tec warrants this product to

be free from defects in workmanship and materials

under normal use for as long as you own this product.

This warranty covers all of the component parts of the

product except batteries. This warranty does not cover

deterioration due to normal wear or damage due to

misuse, alteration, negligence, accidents, or

unauthorized repair. Princeton Tec will repair or replace

parts which are defective in workmanship or materials.

Your authorized Princeton Tec Dealer and Princeton

Tec are the only facilities authorized to repair the

product. After (3) unsuccessful attempts (within the

warranty period) to repair the product, you have the

right to elect replacement of the product or a refund of

the purchase price less allowance for use of the

product. NO INCIDENTAL OR CONSEQUENTIAL

DAMAGES ARE INCLUDED IN THIS WARRANTY.

(Some states do not allow the exclusion or limitation of

incidental or consequential damages, so the above

limitations or exclusions may not apply to you.) This

warranty gives you specific legal rights, and you may

also have other rights which vary from state to state.

Princeton Tec reserves the right to change product

specifications without notice.

Return Policy

If your light fails to operate, follow these simple steps:

1) Check batteries. Replace if necessary.

2) Contact Princeton Tec customer service at

800-257-9080 to request an RMA number to send your

light in for repair or replacement. No warranty repairs

will be accepted without an RMA number.

3) Return the light without batteries to: Princeton Tec,

5198 Rt. 130, Bordentown, NJ 08505. Postage due

and freight collect items will not be accepted.

Princeton Tec

PO Box 8057,

Trenton, NJ 08650

Phone: 609-298-9331

Fax: 609-298-9601

www.princetontec.com

press 2x = Low

press 3x = High

1 MAXBRIGHT

LED

DISTANCE (Meters)

4 15 30

HIGH

LOW

96H

RED

146H

DISTANCE (Meters)

6 15 30

to switch between light

sources, press and hold

button (1-2 seconds)

Figure 3 – Battery Replacement

Remplacement des piles Einlegen der Batterien

Figure 2 – Battery Lockout

verrouillage de la batterie

Akkuverschluss

1 2

Slide up to operate; slide down to prevent accidental activation and eliminate

battery drain.

Pour allumer la lampe, appuyez sur le commutateur pour le faire remonter ;

appuyez de nouveau dessus pour l’escamoter afin d’empêcher tout

fonctionnement involontaire ainsi que la décharge des piles.

Schieben Sie den Schalter nach oben, um die Lampe zu verwenden. Schieben

Sie den Schalter nach unten, um ein unbeabsichtigtes Einschalten und Entladen

der Batterie zu verhindern.

2 1

press 1x = On

RED LED

1 2

Inhaltsverzeichnis

Seite 1 - Figure 2 – Battery Lockout

www.princetontec.comENGLISHFigure 1 – Switch OperationOpération de commutation Betriebsartenschalter* Princeton Tec calculates total burn time as the

Seite 2 - Francais

Einlegen der Batterien – siehe Schema zum Einlegen der Batterien • 2 AAA-Batterien • Alkaline (LR03)- oder Lithium-Batterien • Aufladbare Nickel-Cadm

Kommentare zu diesen Handbüchern

Keine Kommentare

Princeton-tec BYTE Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Beleuchtung Princeton-tec BYTE herunter. Princeton Tec BYTE User Manual [fr] Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Beleuchtung Princeton-tec BYTE